





PRIMARE A35.2
PRICE ON ENQUIRY
Primare A35.2 stereo power amplifier: UFPD 2, 2 × 200 W into 8 Ω, 800 W bridged, balanced XLR and RCA inputs. Available in India from Shivansh Electronics, Kolkata, West Bengal, India.
VISUAL GUIDE — See Every Photo, Spec & Setup Step (PDF)
PRICE ON ENQUIRY. For the price, exclusive offers, delivery timelines, or any other information, please Contact / WhatsApp +91 89818 07755 / +91 91477 00677. We will gladly share a personalised quotation for Shivansh Electronics, Kolkata, West Bengal, India. All payments are processed securely through Razorpay, our secure payment gateway.
Amplifier
| Type | Balanced-input bridgeable stereo power amplifier, 35 Series |
| Amplifier module | Primare UFPD 2 |
| Power supply | Primare APFC |
| Amplifier output, stereo | 2 × 200 W into 8 Ω, 2 × 400 W into 4 Ω |
| Amplifier output, bridged | 1 × 800 W into 8 Ω, 1 × 500 W into 4 Ω |
| Output impedance | < 0.02 Ω |
Inputs
| RCA input | 1 × stereo pair, 15 kΩ impedance |
| XLR input | 1 × stereo pair, 30 kΩ impedance |
| Input sensitivity | RCA: 2 V for 200 W into 8 Ω; XLR: 4 V for 200 W into 8 Ω |
Performance
| Gain | RCA 26 dB; XLR 20 dB |
| Frequency response | 20 Hz - 20 kHz: -0.2 dB |
| Distortion, THD + N | < 0.008 %, 20 Hz - 20 kHz, 10 W at 8 Ω |
| Signal to noise | > 110 dB |
Control
| 12 V trigger | 2 × 3.5 mm, input / output |
| RS232 | Outboard system control port |
| Auto Sense | On / off |
| Input switch | RCA / XLR |
| Gain switch | +6 dB, bridge mode only |
General
| Power consumption | Standby < 0.5 W; operating 28 W < 800 W |
| Dimensions (W × D × H) | 430 × 400 × 145 mm with knobs and connectors; 430 × 382 × 145 mm without knobs and connectors |
| Weight | 11.7 kg |
| Colour | Black or titanium |
Versions
| A35-2-BLACK | Black |
| A35-2-TITANIUM | Titanium |
Product overview
The Primare A35.2 is a powerful balanced-input stereo power amplifier from the 35 Series, using Primare's UFPD 2 amplification technology to deliver 200 W per channel into 8 Ω in stereo and 800 W into 8 Ω in bridged mono mode.
The A35.2 is the most powerful amplifier Primare has designed with its proprietary UFPD 2 analogue class D amplification technology. A completely new UFPD 2 power output module was designed to give the power and performance needed for a statement stereo amplifier, providing immediate and sustained high power output with very low distortion, instantaneous rise time and absolutely linear amplification across the entire bandwidth. The result is a naturally fast, clean and agile sound over an ultra-wide frequency range, with exceptional headroom.
In UFPD 2 a new error amplifier circuit leaves the gain-versus-frequency curve untouched, so the bandwidth does not have to be limited. This gives very low phase shift in the audio band and a larger closed-loop bandwidth, while a custom-made output coil in the second-order filter keeps feedback control working across the entire audio band. The amplification is even more linear and lower in noise, for truly black backgrounds from which music takes on a holographic, three-dimensional, life-like character.
A completely new switch-mode power supply with custom-wound transformers feeds the amplifier module: where the 150-watt I35 uses a 600-watt supply, the 200-watt A35.2 uses a 900-watt supply, delivering 50 % more power to the output modules. The Active Power-Factor Correction (APFC) converter is up to 5 % more efficient than earlier supplies, uses dual PFC converters 180 degrees out of phase to minimise interference with other equipment on the same mains supply, and runs in transition mode to reduce switching losses. The input stage sits on a four-layer circuit board for low noise and an extremely short signal path.
Balanced XLR and single-ended RCA inputs, an OUTPUT switch for stereo or bridged mode, a +6 dB gain switch for bridged use, Auto Sense, a 12 V trigger input and output and RS232 make the A35.2 easy to build into a system. It is made to pair with the PRE35 preamplifier in its various configurations, and can be used as a single stereo amplifier, as a pair for bi-amping, or as a pair in bridged mono mode for 800 W per channel, driving even the most demanding loudspeakers or a powerful multi-channel system. The standby button sits discreetly in the Primare logo on the faceplate: Scandinavian design in the spirit of lagom, not too much, not too little.
| Amplifier output into 8 Ω (2 × 400 W into 4 Ω) | 2 × 200 W |
| Bridged amplifier output into 8 Ω | 1 × 800 W |
| THD + N, 20 Hz - 20 kHz, 10 W at 8 Ω | < 0.008 % |
| Signal to noise | > 110 dB |
Key features
- UFPD 2 amplification: amplifier output 2 × 200 W into 8 Ω, 2 × 400 W into 4 Ω
- Bridged mono mode: amplifier output 1 × 800 W into 8 Ω, 1 × 500 W into 4 Ω
- Completely new UFPD 2 power output module, the most powerful Primare has designed
- 900-watt APFC switch-mode power supply with custom-wound transformers
- Balanced XLR (30 kΩ) and RCA (15 kΩ) inputs with an input selector switch
- +6 dB gain switch for bridged mode
- Four-layer input-stage circuit board for low noise and an extremely short signal path
- THD + N < 0.008 % and signal to noise > 110 dB
- Auto Sense switch-on from standby and auto-standby after 20 minutes without signal, which can be disabled
- 12 V trigger in and out for daisy-chaining further amplifiers, and RS232 control
- Standby button set into the Primare logo, in black or titanium
Made for
- Stereo systems with the PRE35 preamplifier or another preamplifier
- Demanding loudspeakers that need high, sustained power
- Bi-amping a pair of loudspeakers with two A35.2 amplifiers
- Two A35.2 amplifiers in bridged mono mode for 800 W per channel
- Home theatre and multi-channel systems driven from a processor
- Custom installations with trigger and RS232 control
In the box
- A35.2 stereo power amplifier
- Mains cable
- IR/Trigger cable
- AC Polarity Pen (with batteries)
Connections
- 1 × balanced stereo input, XLR (L and R), 30 kΩ
- 1 × stereo input, RCA (L and R), 15 kΩ
- Loudspeaker terminals, left and right, for bare wires, spade terminals or banana plugs
- 12 V trigger in and trigger out, 3.5 mm
- RS232 outboard system control port
- INPUT (RCA / XLR), OUTPUT (stereo / bridged), GAIN (+6 dB) and SENSE switches
- Mains inlet with power switch on the back panel
Finishes
- Black
- Titanium
Primare A35.2: frequently asked questions
How do I use the A35.2 in bridged mode?
Switch the amplifier off at the back panel, set the OUTPUT switch to BRIDGED, connect the signal to the left RCA or XLR input, set the INPUT switch to match, and connect the loudspeaker between the RIGHT + and LEFT - terminals. The GAIN switch can be set to +6 dB for a higher output. Bridged mode gives up to four times the output power to a single loudspeaker: 800 W into 8 Ω.
Which preamplifier suits the A35.2?
Primare describes the A35.2 as the obvious match for the PRE35 preamplifier in its various configurations. It connects to any preamplifier or processor through its RCA or balanced XLR inputs.
Can the A35.2 switch on with my preamplifier?
Yes. Connect the TRIG OUT of a Primare processor or preamplifier to TRIG IN on the A35.2 with a mono 3.5 mm jack cable. TRIG OUT on the A35.2 can be daisy-chained to further A35 Series amplifiers. With the SENSE switch on, the amplifier also wakes when a signal arrives and returns to standby after 20 minutes without signal.
How should I position my loudspeakers?
Primare recommends placing the loudspeakers about 2-3 m apart, at least 20 cm from the rear wall and at least 50 cm from any side wall, with the tweeters at head height when you are seated.
How do I get the best sound from the A35.2?
Use the supplied AC Polarity Pen so the live pin of the mains cable goes to the left-hand pin of the power connector, viewed from the back. The amplifier starts to sound its best after a burn-in of about 24 hours, with a further smaller improvement over at least another three days of playing.
Where can I buy the Primare A35.2 in India?
The Primare A35.2 is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.
Workflow 1: Stereo listening room with the PRE35
Music lovers building a two-channel pre/power system for a dedicated listening room.
Connections
| Connect | To |
|---|---|
| PRE35 balanced XLR outputs | A35.2 XLR inputs |
| PRE35 TRIG OUT | A35.2 TRIG IN (mono 3.5 mm) |
| A35.2 speaker terminals | Pair of passive loudspeakers |
Setup
- Connect the preamplifier to the XLR inputs with balanced cables and set the INPUT switch to XLR.
- Connect red to + and black to - on both loudspeakers.
- Run a trigger cable from the preamplifier TRIG OUT to TRIG IN so both switch on together.
- Check the mains plug with the AC Polarity Pen and switch on at the back panel.
Tip: Place the loudspeakers about 2-3 m apart, at least 20 cm from the rear wall and 50 cm from side walls.
Workflow 2: Bridged mono pair for demanding loudspeakers
Owners of large, demanding loudspeakers who want the most power.
Connections
| Connect | To |
|---|---|
| Preamplifier left output | First A35.2 left XLR or RCA input |
| Preamplifier right output | Second A35.2 left XLR or RCA input |
| Each A35.2 RIGHT + and LEFT - terminals | One loudspeaker |
Setup
- Switch both amplifiers off at the back panel.
- Set the OUTPUT switch on each to BRIDGED and the INPUT switch to RCA or XLR.
- Connect each loudspeaker between the RIGHT + and LEFT - terminals of its amplifier.
- Optionally set the GAIN switch to +6 dB on both for a higher output.
Tip: Bridged mode gives 1 × 800 W into 8 Ω per amplifier: no short wire is needed, whatever the back-panel label shows.
Workflow 3: Bi-amped loudspeakers
Listeners with bi-wire loudspeakers who want separate amplification for the bass and treble sections.
Connections
| Connect | To |
|---|---|
| Preamplifier outputs | Two A35.2 amplifiers (RCA or XLR) |
| First A35.2 speaker terminals | Bass terminals of both loudspeakers |
| Second A35.2 speaker terminals | Treble terminals of both loudspeakers |
Setup
- Feed both amplifiers from the preamplifier outputs.
- Connect one A35.2 to the bass terminals and the other to the treble terminals.
- Daisy-chain TRIG OUT of the first amplifier to TRIG IN of the second.
- Make sure the GAIN and INPUT switches are set the same on both amplifiers.
Tip: Primare names bi-amping with a pair of A35.2 amplifiers as one of its configuration options.
Workflow 4: Home theatre front channels
Home theatre owners who want high power for the main speakers.
Connections
| Connect | To |
|---|---|
| AV processor front left / right pre-outs | A35.2 RCA or XLR inputs |
| A35.2 speaker terminals | Front left and right loudspeakers |
| Processor 12 V trigger out | A35.2 TRIG IN |
Setup
- Connect the processor's front pre-outs to the A35.2 inputs and set the INPUT switch.
- Connect the front loudspeakers to the speaker terminals.
- Link the processor trigger output to TRIG IN so the amplifier follows the system.
- Set the processor speaker levels for the front channels.
Tip: A35.2 TRIG OUT can pass the trigger on to further A35 Series amplifiers for the other channels.
Workflow 5: Auto-on living-room system
Families who want the amplifier to wake when music starts without extra switching.
Connections
| Connect | To |
|---|---|
| Preamplifier or streamer with volume control | A35.2 RCA inputs |
| A35.2 speaker terminals | Living-room loudspeakers |
Setup
- Connect the source to the RCA inputs and set the INPUT switch to RCA.
- Switch the SENSE switch to ON.
- The A35.2 comes out of standby when a signal is sensed.
- It returns to standby after 20 minutes without signal.
Tip: To keep the amplifier on, press and hold the front-panel button until the light flashes twice; switching off and on at the back restores auto-standby.
Workflow 6: Custom-installed media room
Installers and owners of rack-based media rooms and whole-home systems.
Connections
| Connect | To |
|---|---|
| Home-automation controller | A35.2 RS232 port (null-modem cable) |
| Controller or preamplifier trigger | A35.2 TRIG IN |
| A35.2 TRIG OUT | Next A35 Series amplifier TRIG IN |
Setup
- Connect the controller to the RS232 port with a twisted (null-modem) cable.
- Link the trigger from the preamplifier or controller to TRIG IN.
- Daisy-chain TRIG OUT to further A35 Series amplifiers.
- Allow ventilation in the rack and check mains polarity with the AC Polarity Pen.
Tip: Always disconnect mains power before connecting or disconnecting any cables.








