SCHOEPS CMC 1 K

Product overview

The SCHOEPS CMC 1 K is the version of the small Colette microphone amplifier CMC 1 with a permanently attached cable: identical to the CMC 1 U, but with a fixed cable in place of the built-in XLR connector.

It is a complete alternative to the renowned CMC 6 and fully compatible with all existing MK capsules and with Colette active accessories such as the CUT 60 low-cut filter and the RC tubes. The housing is only 29 mm long and weighs about 28 g without the cable.

The CMC 1 K is available with different cable lengths and plugs: the standard version has a 5 m cable with an XLR-3M connector, and two 0.5 m versions with a 3-pin Lemo plug connect to pocket transmitters with P12 or P48 powering. Special versions with any cable length are also available. Like every CMC 1, it reaches 135 dB-SPL with the MK 4, draws only 2 mA at 48 V and carries the SCHOEPS RFI Shield.

Key features

• Version of the CMC 1 with a permanently attached cable, otherwise identical to the CMC 1 U
• Complete alternative to the renowned CMC 6
• Fully compatible with all MK capsules and Colette active accessories such as the CUT 60 and RC tubes
• Standard: 5 m cable with XLR-3M connector
• 0.5 m versions with 3-pin Lemo plug for pocket transmitters with P12 or P48
• Special versions with any cable length
• SCHOEPS RFI Shield; works on P48 and P12 phantom power
• SGC miniature stand mount with swivel included

Made for

• Hanging microphones with a miniature cable hanger
• Table use with a miniature table stand
• Pocket transmitters with P12 or P48 powering
• Every application where a short, light microphone with a fixed cable is wanted

In the box

• CMC 1 K microphone amplifier with attached cable (5 m with XLR-3M, or 0.5 m with 3-pin Lemo, depending on the version)
• SGC miniature stand mount with swivel
• An MK capsule of the Colette system is needed, available separately

SCHOEPS CMC 1 K: frequently asked questions

How does the CMC 1 K differ from the CMC 1 U?

The CMC 1 K is identical to the CMC 1 U, but instead of a built-in XLR connector it has an attached cable. Its housing is 29 mm long.

Which cable versions are available?

No. 132013 with a 5 m cable and XLR-3M connector (standard), and No. 132016 and No. 132017 with a 0.5 m cable and 3-pin Lemo plug for two types of pocket transmitter. Special versions with any cable length are available; specified lengths may vary by up to 5 %.

Which capsules fit?

All existing MK capsules, for example the MK 2, MK 21, MK 22, MK 4, MK 41 and MK 8, together with Colette active accessories such as the CUT 60 and RC tubes.

Which accessories are recommended?

The CUT 60 low-cut filter, the HC miniature cable hanger, the MKH sleeve for anchoring a hanging cable with a nylon string, and the TC, TC 2 and T 20 miniature table stands.

Where can I buy the SCHOEPS CMC 1 K in India?

The SCHOEPS CMC 1 K is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Hanging microphone

Engineers in concert halls, churches and studios.

Connections

Setup

1. Screw the MK capsule onto the CMC 1 K.
2. Hang it on its own cable with the HC cable hanger.
3. Anchor the cable with the MKH sleeve and a nylon string if needed.
4. Switch on phantom power and set the gain.

Tip: The fixed cable and the very short housing keep a hanging microphone discreet.

Workflow 2: On a pocket transmitter

Sound recordists working with radio links.

Connections

Setup

1. Choose the 0.5 m Lemo version that matches the transmitter type.
2. Plug the microphone into the transmitter.
3. Set the transmitter to P12 or P48 and check the level.

Tip: Power consumption is lower at 12 V, an advantage for battery-powered operation.

Workflow 3: On the table

Installers and recordists covering speech at tables.

Connections

Setup

1. Place the microphone on a miniature table stand.
2. Aim the capsule at the talker position.
3. Set the gain for speech.

Tip: The cable leaves the microphone directly, without a separate connector.

Workflow 4: On a stand with the SGC

Engineers on stage and in the studio.

Connections

Setup

1. Fit the microphone into the included SGC.
2. Angle it towards the source.
3. Connect and set the gain.

Tip: Any MK capsule turns the CMC 1 K into a complete Colette microphone.

Workflow 5: With a low-cut filter

Users who need to reduce low-frequency noise.

Connections

Setup

1. Place the CUT 60 between capsule and amplifier.
2. Connect as usual.
3. Set the gain.

Tip: All Colette active accessories are compatible with the CMC 1 K.

Workflow 6: Custom cable length

Installations with fixed cable routes.

Connections

Setup

1. Specify the cable length needed for the installation.
2. Install the microphone with its attached cable.
3. Connect to the preamp with phantom power.

Tip: Special versions with any cable length are available.