TASCAM DR-10L Pro

Product overview

The TASCAM DR-10L Pro is an ultra-compact 32-bit float field recorder with a TM-10L lavalier microphone, made to be worn out of sight by talent, presenters and performers.

For AV creators, weddings and events, film shoots, stage performances and field recording, the DR-10L Pro captures a whisper, a scream and everything in between with ultra-low noise and no need to fine-tune gain. Its dual AD converters record 32-bit float audio across a huge dynamic range, so takes are never lost to poor levels. At 65 g with batteries it hides easily with the included belt clip, two AAA batteries last up to 24.5 hours, and files are saved about every 20 seconds. LTC jam sync, wireless timecode and app control of up to five units with the optional AK-BT1 adapter suit professional productions.

Key features

• Ultra-lightweight, wearable design: 53 x 50.7 x 21.4 mm, 65 g with batteries
• TM-10L lavalier microphone with clothing clip and windscreen, 1.6 m cable, screw-lock connector
• 32-bit float with dual AD converters: no need to set input gain
• WAV (BWF) 16 / 24-bit or 32-bit float at 44.1 / 48 kHz; MP3 at 128 or 192 kbps
• microSD, microSDHC and microSDXC cards up to 512 GB
• LTC jam sync with an unlimited number of DR-10L Pro units over the 3.5 mm input
• Wireless timecode and app control with the optional AK-BT1 Bluetooth adapter
• Free TASCAM RECORDER CONNECT app for iOS, iPadOS and Android: control up to five units
• High-precision 0.5 ppm TCXO clock: drift within about one frame per 24 hours
• Auto File Save, slide REC switch with one-touch recording, key lock, OLED display and headphone output

The stealthiest recorder and mic

Fitting in the palm of your hand and weighing just 65 g, the DR-10L Pro is easy to hide at film shoots, weddings and stage performances. The belt clip attaches securely to clothing, the TM-10L clips discreetly in place, and the screw-lock connector keeps the mic firmly attached.

Dual ADCs and 32-bit float for fast setup

The default 32-bit float mode uses dual AD converters to capture sounds across a huge dynamic range without distortion or excessive noise. There is no need to adjust input gain, so you set up faster with confidence. The TM-10L handles loud sound pressure without distorting, a perfect match for 32-bit float recording.

Sync smarter: LTC and wireless timecode

From firmware 2.0 the DR-10L Pro supports LTC jam sync through its top-mounted 3.5 mm input, with frame rates from 23.98 to 30 fps. After syncing, unplug the generator and record with the lavalier while the high-precision clock keeps time. With the optional AK-BT1, the recorder can also receive timecode wirelessly from a supported wireless timecode system, so audio lines up with every camera.

Remote control with TASCAM RECORDER CONNECT

With the AK-BT1 fitted, the free app controls up to five recorders, shows device status and real-time waveforms, names each unit (for example 'Bride' and 'Groom') with an identification colour, writes project, scene and take metadata (BEXT, iXML), stores presets and sets the clock from your phone or tablet.

In the box

• TASCAM DR-10L Pro
• Belt clip
• USB cable (Type-A to Type-C)
• TM-10L lavalier microphone
• Microphone clip
• Windscreen
• Start-up Guide (including warranty)
• TASCAM ID registration guide
• RX Elements download card

The download card is for the RX Elements audio repair software bundled with the DR-10L Pro. A microSD card and 2 AAA batteries are sold separately; the AK-BT1 Bluetooth adapter is optional.

TASCAM DR-10L Pro: frequently asked questions

Do I need to set the recording level?

No. In the default 32-bit float mode the dual AD converters capture the full dynamic range, so levels can be set later in editing. REC LEVEL, limiter and auto level are available for 16 and 24-bit recording.

How does timecode work on the DR-10L Pro?

Connect a timecode generator's LTC output to the input jack and jam sync with menu item LTC SYNC; the timecode then runs on the internal clock and is written to the WAV (BWF) files. With the optional AK-BT1 it can also receive wireless timecode.

How many units can I control with the app?

Up to five DR-10L Pro units at once with the free TASCAM RECORDER CONNECT app on iOS, iPadOS or Android. Each recorder needs an AK-BT1 Bluetooth adapter.

How long do the batteries last?

About 24.5 hours with lithium AAA batteries, about 16.5 hours with alkaline and about 11.5 hours with NiMH (WAV 48 kHz, 32-bit float, mono, headphones not connected). USB bus power is also supported.

Where can I buy the TASCAM DR-10L Pro in India?

The TASCAM DR-10L Pro is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Wedding ceremony with several speakers

Give the couple and the officiant their own recorder for clean vows and speeches.

Connections

Setup

1. Insert lithium AAA batteries and a microSD card in each unit and set the date and time.
2. Name each unit in the TASCAM RECORDER CONNECT app, for example 'Bride' and 'Groom'.
3. Clip the lavaliers on and start all units from the app, or by sliding each REC switch.
4. Check status and waveforms in the app during the ceremony; stop recording from the app at the end.

Tip: 32-bit float means a sudden laugh or applause will not ruin the recording.

Workflow 2: Film shoot with LTC timecode

Keep a wireless-free audio recorder on the actor in perfect sync with the cameras.

Connections

Setup

1. Connect the timecode generator to the input jack with a stereo mini cable.
2. Select menu item 29: LTC SYNC and confirm the frame rate used by the generator.
3. Disconnect the generator and connect the lavalier; timecode keeps running on the 0.5 ppm clock.
4. Record; the timecode is written to the WAV (BWF) files for alignment in editing.

Tip: Never monitor an LTC signal on headphones: its level is extremely high.

Workflow 3: Multi-camera event with wireless timecode

Sync several recorders and cameras without cables using the optional AK-BT1.

Connections

Setup

1. Fit the AK-BT1 under the locking cover on top of the recorder.
2. Set 25: BLUETOOTH to TIMECODE; the unit searches for and pairs with the timecode system.
3. Hold ENTER to show the received timecode on the display.
4. Record; files carry timecode that lines up with the cameras.

Workflow 4: Interviews and documentaries

Record each interviewee separately with clean, consistent sound.

Connections

Setup

1. Clip the lavalier about a hand's width below the chin and fit the windscreen outdoors.
2. Set LOW CUT to reduce wind or air-conditioning rumble.
3. Monitor on headphones before and during recording.
4. Clean up noise later with the bundled RX Elements audio repair software.

Tip: Turn on PEAK MARK to find any loud moments quickly in editing.

Workflow 5: Stage performances and presentations

Capture a performer's or presenter's voice without visible equipment.

Connections

Setup

1. Slide and hold the switch towards REC from power off for one-touch recording.
2. Keys are locked during recording except stop, headphone volume and remaining time.
3. Auto File Save writes the file about every 20 seconds during the show.
4. After the show copy the files to a computer over USB Type-C.

Tip: Set TIME MARK to add marks every 5 to 60 minutes for long performances.

Workflow 6: Field and voice recording

A tiny recorder for vlogs, voice notes and ambience on the move.

Connections

Setup

1. Choose WAV 32-bit float for quality or MP3 for long recordings.
2. Select MONO or POLY file type as needed.
3. Record with the slide switch and check the take on headphones.
4. Transfer files over USB mass storage; balance 32-bit float levels with TASCAM Audio File Manager.

Tip: USB bus power can run the recorder from a computer or power bank port.