TOTEM ACOUSTIC Wind Design product guide and data sheet cover
‹
TOTEM ACOUSTIC Wind Design product guide and data sheet coverTOTEM ACOUSTIC Wind Design data sheet page 2: Blowing in the WindTOTEM ACOUSTIC Wind Design data sheet page 3: Set-up and specifications
›

Brand: TOTEM ACOUSTIC

TOTEM ACOUSTIC Wind Design

PRICE ON ENQUIRY

Category: Floorstanding Speakers | Series: WIND

Totem Acoustic Wind Design three-way tower: hand-selected drivers, twin midranges, six-layer multi-coated finish, articulating claw. Available in India from Shivansh Electronics, Kolkata, West Bengal, India.


WhatsApp
VISUAL GUIDE — See Every Photo, Spec & Setup Step (PDF)

PRICE ON ENQUIRY. For the price, exclusive offers, delivery timelines, or any other information, please Contact / WhatsApp +91 89818 07755 / +91 91477 00677. We will gladly share a personalised quotation for Shivansh Electronics, Kolkata, West Bengal, India. All payments are processed securely through Razorpay, our secure payment gateway.


TECHNICAL SPECIFICATIONTech SpecsDESCRIPTIONDescriptionREAL-WORLD WORKFLOWSReal-World Workflows

Acoustic performance

TypeThree-way floorstanding loudspeaker, four drivers
Frequency response24 Hz - 21 kHz ± 3 dB (in room)
Sensitivity87 dB
Impedance4 Ω
Recommended amplifier power80 - 250 W
CrossoverWoofer to mids: 2nd order / 2nd order; mids to tweeter: 2nd order / 2nd order; hard-wired, exclusive components

Drivers

Woofer8.5 in (21.59 cm), cast frame, specially damped, high power handling, long throw
Mid-woofers (2)3 in (7.62 cm) voice coil, cast frame, high power handling, wrap-around neodymium magnet structure, accurate linear throw
Tweeter1 in (2.54 cm) alloy dome, flexible linear suspension, special low-resonance chamber

Connections

Speaker terminalsBi-wireable, gold premium connectors
Accepted connectionsBare wire, pin connectors, banana plugs, spade lugs 8.1 - 9 mm (5/16 - 3/8 in)

Placement

Placement from rear wall3 - 7 ft (91.44 - 213.36 cm)
Placement distance apart6 - 14 ft (182.88 - 426.72 cm)
Break-in time200 - 250 hours

Physical

Dimensions (W × H × D)271.8 × 1125.2 × 355.6 mm (10.7 × 44.3 × 14 in), over maximum size
Weight34 kg (74.8 lb)
FinishSix-layer multi-coated polyester
DecouplingFront articulating claw, rear aluminium skid plate
GrilleMagnetic grille, optional
Made inCanada

Versions

WIND-DESIGN-DUSKDusk
WIND-DESIGN-FIREFire
WIND-DESIGN-ICEIce

Product overview

The Totem Acoustic Wind Design takes the four-driver, three-way Wind floorstander a step further: hand-selected drivers, exclusive crossover components, six-layer multi-coated polyester finishes and a new articulating claw that slants the baffle back for precise spatial alignment.

Going a step further than the original Wind, the Wind Design is refined to the highest sonic tolerances. Its hand-selected drivers and exclusive crossover components give ultra-broad, all-axis soundstaging. Totem designed it like a musical instrument, for sonic expressivity that pulls the listener inside the music.

The driver line-up is the Wind's: a specially damped 8.5-inch cast-frame woofer with long-throw characteristics, two mid-woofers with 3-inch voice coils, cast frames and wrap-around neodymium magnet structures, and a 1-inch alloy dome tweeter with flexible linear suspension in a special low-resonance chamber. An extreme-quality hard-wired crossover joins them with second-order slopes, and the speaker images on and off axis as a point source.

The six-layer multi-coated finish adds structural rigidity, and its deep lustre does more than shine: it allows a more cohesive acoustic behaviour. At the base of the front baffle sits a new articulating claw that can be adjusted to slant the baffle back for precise spatial alignment and optimal bass loading, while a rear aluminium skid plate with two formed feet decouples the cabinet from the floor for further spatial performance.

The Wind Design suits larger rooms, with 3 - 7 ft (91.44 - 213.36 cm) from the rear wall and 6 - 14 ft (182.88 - 426.72 cm) between the speakers, and an amplifier of 80 - 250 W. It is finished in Dusk, Fire or Ice.

Frequency response (± 3 dB, in room) 24 Hz - 21 kHz
Sensitivity 87 dB
Recommended amplifier power 80 - 250 W
Impedance 4 Ω

Key features

  • Exclusive four-driver three-way system with hand-selected drivers
  • Exclusive crossover components in an extreme-quality hard-wired crossover, second order throughout
  • 8.5-inch cast-frame woofer, specially damped, long throw
  • Two mid-woofers with 3-inch voice coils and wrap-around neodymium magnet structures
  • 1-inch alloy dome tweeter in a special low-resonance chamber
  • Ultra-broad, all-axis soundstaging and point-source imaging on and off axis
  • Six-layer multi-coated polyester finishes for extra structural rigidity
  • Articulating claw at the front to slant the baffle back, plus a rear skid-plate decoupling system
  • Bi-wireable gold premium speaker terminals
  • Finishes: Dusk, Fire, Ice; optional magnetic grille
  • Made in Canada

Made for

  • Stereo music listening in larger living rooms and dedicated listening rooms
  • Rooms where the speaker is also a visual centrepiece
  • Front left and right channels of a home theatre
  • Music, films, TV and video games

Placement and set-up

  • 3 - 7 ft (91.44 - 213.36 cm) from the rear wall
  • 6 - 14 ft (182.88 - 426.72 cm) apart
  • No toe-in is needed; if the speakers are more than 8 ft (2.5 m) apart and the room affects the imaging, angle one slightly, then the other
  • Adjust the articulating claw to set the rake of the baffle for bass loading and spatial alignment
  • Fit the skid plate with its feet at the back of the cabinet, using the supplied hardware
  • Break-in: 200 - 250 hours of music, without very loud levels during that time

In the box

  • Wind Design loudspeaker, with jumpers fitted on the terminals
  • Articulating claw with threaded insert
  • Rear skid plate with fixing hardware

Connections

  • Bi-wireable gold premium speaker terminals (two sets), for single-wire, bi-wire or bi-amp connection
  • The terminals accept bare wire (wrapped around or through the post), pin connectors, banana plugs and spade lugs of 8.1 - 9 mm (5/16 - 3/8 in)
  • Jumpers between the two sets of terminals for single-wire connection

Finishes

  • Dusk: six-layer multi-coated polyester
  • Fire: six-layer multi-coated polyester
  • Ice: six-layer multi-coated polyester

Totem Acoustic Wind Design: frequently asked questions

How does the Wind Design differ from the Wind?

It shares the Wind's four-driver, three-way layout and published figures, but goes a step further with hand-selected drivers, exclusive crossover components, six-layer multi-coated polyester finishes in Dusk, Fire and Ice, a front articulating claw and a rear skid-plate decoupling system.

What does the articulating claw do?

It sits at the base of the front baffle and can be adjusted to slant the baffle back, setting the rake of the cabinet for optimal bass loading and precise spatial alignment. Together with the aluminium skid plate at the rear, it decouples the cabinet from the floor.

What amplifier power does the Wind Design need?

Totem recommends 80 - 250 W into its 4 Ω impedance. More clean amplifier power is safer than an amplifier pushed into distortion, the most common cause of speaker damage: turn the volume down as soon as distortion starts.

How much space does the Wind Design need?

Totem recommends 3 - 7 ft (91.44 - 213.36 cm) from the rear wall and 6 - 14 ft (182.88 - 426.72 cm) between the speakers. No toe-in is needed for an accurate, three-dimensional soundstage.

Can the Wind Design be bi-wired or bi-amped?

Yes. The bi-wireable gold terminals come with jumpers fitted for a single cable; remove them to bi-wire or bi-amp, and make every connection with the equipment switched off.

Where can I buy the Totem Acoustic Wind Design in India?

The Totem Acoustic Wind Design is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Stereo listening room

Music lovers building a dedicated listening room or a large living-room system.

Connections

ConnectTo
Streamer, CD player or turntable with phono stageIntegrated amplifier input
Integrated amplifier L / R speaker outputs (80 - 250 W recommended, 4 Ω capable)Wind Design terminals, jumpers in place

Setup

  1. Fit the skid plate at the rear and the articulating claw at the front of each cabinet, protecting the finish with the packaging foam.
  2. Stand the speakers 3 - 7 ft (91.44 - 213.36 cm) from the rear wall and 6 - 14 ft (182.88 - 426.72 cm) apart.
  3. Sit about 1.5 times the speaker spacing away and point the speakers straight ahead.
  4. With everything switched off, connect red to red and black to black, keeping the jumpers in place.
  5. Play music for 200 - 250 hours at moderate levels to break the speakers in.

Tip: Closer to the rear wall gives more bass but less soundstage depth: move the speakers in small steps.

Workflow 2: Fine-tuning the baffle rake

Listeners who want to lock in the image and bass at their own seat.

Connections

ConnectTo
Amplifier speaker outputsWind Design terminals

Setup

  1. Set the speakers in their final positions first.
  2. Turn the threaded insert of the articulating claw to slant the baffle back a little.
  3. Listen to familiar recordings for bass weight and the focus of the centre image.
  4. Adjust both speakers equally in small steps until the image locks in place.

Tip: Change one thing at a time - position, then rake - so you can hear what each adjustment does.

Workflow 3: Bi-wired or bi-amped stereo

System builders running separate cables or two amplifiers to each speaker.

Connections

ConnectTo
Amplifier outputs (one amplifier for bi-wire, two for bi-amp)Upper and lower Wind Design terminals, jumpers removed

Setup

  1. Switch every component off and check the amplifier manuals for bi-amp connection.
  2. Remove the jumpers between the two sets of terminals.
  3. Connect the lower and upper terminals with separate cables, red to red and black to black.
  4. With two amplifiers, set matching levels and start at a low volume.
  5. Raise the volume gradually within the 80 - 250 W recommended range.

Tip: Lack of bass or image usually means reversed polarity on one connection.

Workflow 4: 5.1 home theatre in a large living room

Families who want the Wind Design as the front pair of a film and music system.

Connections

ConnectTo
TV or media player HDMIAV receiver HDMI input
AV receiver front L / R speaker outputsWind Design terminals
Centre, surround and subwoofer outputsMatching centre, surround speakers and subwoofer

Setup

  1. Place the pair as for stereo, either side of the screen, within the recommended spacing.
  2. Centre a Totem centre channel on the screen, 20 - 30 in (50.8 - 76.2 cm) above the floor, ideally equidistant from the front pair.
  3. Place the surrounds behind and beside the listening area at about 6 ft (183 cm) high.
  4. Place the subwoofer almost anywhere; closer to a corner gives more bass.
  5. Run the receiver's speaker set-up and check every channel's polarity.

Tip: Totem voices its centre channels to match specific main speakers: check the official pairing.

Workflow 5: 7.1 dedicated cinema room

Home cinema owners who want a statement front pair in a dedicated room.

Connections

ConnectTo
Media player HDMIAV processor or receiver HDMI input
Front L / R outputs (via power amplifier if needed)Wind Design terminals
Centre, side and rear surround outputsCentre and four surround speakers

Setup

  1. Place the front pair with the recommended rear-wall distance and spacing.
  2. Set the centre channel on the screen axis, 20 - 30 in (50.8 - 76.2 cm) above the floor.
  3. Place side surrounds beside and slightly behind the seats at about 6 ft (183 cm), and rear surrounds behind the listening position.
  4. Connect every speaker with the equipment switched off.
  5. Fine-tune the front pair's position and rake before level calibration.

Tip: A room with a variety of materials gives a more harmonised sound than a bare, hard room.

Workflow 6: Vinyl and music room

Record collectors who want a full-range floorstander that is also a design piece.

Connections

ConnectTo
TurntablePhono stage
Phono stage outputIntegrated amplifier line input
Amplifier speaker outputsWind Design terminals

Setup

  1. Keep the turntable on a stable surface away from the speakers.
  2. Fit the claw and skid plate and place the speakers 3 - 7 ft from the rear wall and 6 - 14 ft apart.
  3. Connect the amplifier with the jumpers in place.
  4. Listen at moderate levels during the 200 - 250 hour break-in.

Tip: Gradual experimentation with position is the key to the best image in your room.

Request a Quote

TOTEM ACOUSTIC Wind Design

Explore all the categories

Studio to stage, every category —

View all ›

Explore all the brands

Genuine gear from leading audio brands —

View all ›