XVIVE U35D Dual Wireless System for Audio

Product overview

The XVIVE U35D Dual Wireless System for Audio is two U35 Microphone Wireless System sets in one package, for 5.8 GHz wireless connections from a mixer to powered PA speakers, for faster setup and teardown without cables.

The U35D includes two U35 transmitters and two U35 receivers. Run wirelessly from a PA mixing console to powered main speakers, between powered mains or between powered monitors, in stereo or in multiple mono, or use the two sets with two dynamic microphones. Each set is a 5.8 GHz True Diversity system that avoids interference from common 2.4 GHz devices, with automatic scanning for the best of 6 channels, 24-bit / 48 kHz audio, a 20 Hz - 20 kHz (-3 dB) frequency response, 110 dB dynamic range, 0.2 % total harmonic distortion and 5 ms latency, and a range of up to 30.5 m (100 ft) in line of sight.

Key features

• Two U35 sets: 2 transmitters and 2 receivers
• Stereo wireless from the mixer's left and right outputs to two powered speakers
• Dual and multiple mono: one transmitter can feed two or more receivers
• Two dynamic microphones into a mixer or other XLR-input device
• 5.8 GHz True Diversity with automatic scanning for the best of 6 channels
• 24-bit / 48 kHz audio, 20 Hz - 20 kHz, 110 dB dynamic range and signal-to-noise ratio
• Mic and Line modes on the transmitters (0 dB / -10 dB)
• Internal rechargeable batteries: up to 5 hours
• XLR female to XLR male adapter included for mixers with outputs close together

Stereo PA and DJ systems

Connect transmitter 1 to the left main XLR output of the mixer and receiver 1 to the XLR input of the left powered speaker, then transmitter 2 to the right main output and receiver 2 to the right speaker. Each set is switched on and set to its own channel; the second set must use a different channel than the first.

Dual and multiple mono

A small mono system with one loudspeaker needs only one U35 set. For dual mono, connect one transmitter to the mixer's output and U35 receivers to the XLR inputs of two powered speakers, and set all three units to the same channel: both speakers get the same mono signal. One U35 transmitter can transmit to more than two receivers, so the same signal can go to three or more powered cabinets or monitors, with one U35 receiver per cabinet.

Extend and adapt

If the XLR outputs of the mixer are very close together, the included XLR adapter moves one transmitter out of the way of the transmitter plugged into the next channel. An XLR cable of any length (not included) does the same, and XVIVE notes that a cable extension can also resolve wireless interference when many wireless units are close to each other.

Transmitters, receivers and batteries

Each U35 transmitter has an XLR (female) input with a grounding spring and a lock button, a MIC / LINE input switch (0 dB / -10 dB), power, mute and channel switches, channel and power LEDs and a USB charging port. Each U35 receiver has an XLR (male) output, power and channel switches (hold the channel button for 3 seconds to scan for the best channel), channel, RF and power LEDs and a USB charging port. Both units have internal rechargeable lithium-ion batteries for up to 5 hours; each pair charges together from its dual-USB cable and a 5 V / 2 A USB charger, a full charge taking about 2.5 hours.

In the box

• 2 x U35 transmitter
• 2 x U35 receiver
• 2 x USB cable (dual-USB charging cable for each pair)
• 1 x XLR female to XLR male adapter
• 2 x bag (carry pouch for each pair)
• Manual

FAQs

Can the XVIVE U35D send one signal to more than two speakers?

Yes. One U35 transmitter can transmit to more than two receivers on the same channel, so a multiple mono setup only needs one U35 receiver for each powered speaker or monitor.

Can the U35D be used with microphones?

Yes. XVIVE states that the U35D can be used with two dynamic microphones, connected to a mixer or other XLR-input audio device.

Can the U35D be used with microphones?

Yes. XVIVE states that the U35D can be used with two dynamic microphones.

Where can I buy the XVIVE U35D Dual Wireless System for Audio in India?

The XVIVE U35D Dual Wireless System for Audio is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Stereo mixer to two powered speakers

PA and DJ systems with left and right powered speakers.

Connections

Setup

1. Plug transmitter 1 into the left main output and receiver 1 into the left speaker.
2. Switch them on and set both to the same channel.
3. Plug transmitter 2 into the right main output and receiver 2 into the right speaker.
4. Set set 2 to the same channel on both units, different from set 1.

Tip: Set the transmitters to LINE for mixer outputs.

Workflow 2: Dual mono to two speakers

Mono PA systems with two powered speakers.

Connections

Setup

1. Plug one transmitter into the mixer's output.
2. Plug a U35 receiver into each powered speaker.
3. Set all three units to the same channel.

Tip: Both speakers get the same mono signal.

Workflow 3: Multiple mono to three or more cabinets

Events with several powered cabinets or monitors.

Connections

Setup

1. Plug the transmitter into the mixer output.
2. Plug one U35 receiver into each powered cabinet or monitor.
3. Set the transmitter and every receiver to the same channel.

Tip: Additional U35 receivers are available on their own (U35R).

Workflow 4: Mixer to powered mains or monitors

Venues where speaker cables would cross a crowded floor.

Connections

Setup

1. Plug the transmitter into the console output.
2. Plug the receiver into the powered speaker's XLR input.
3. Switch on and set the same channel.

Tip: The sets can also run between powered mains or between powered monitors.

Workflow 5: Two wireless dynamic microphones

Two singers or speakers.

Connections

Setup

1. Plug a transmitter onto each microphone.
2. Plug both receivers into the mixer inputs.
3. Give each set its own channel (hold a receiver's channel button for 3 seconds to scan).
4. Set the transmitters to MIC.

Tip: Works with XLR dynamic and battery-powered condenser microphones.

Workflow 6: Outputs close together

Mixers with tightly spaced XLR outputs.

Connections

Setup

1. Plug the included adapter into one output.
2. Plug a transmitter into the adapter and the other transmitter into the next output.
3. Or use an XLR cable (not included) as an extension.

Tip: A cable extension can also resolve interference when many wireless units are close together.