ECLER PULSO-6

Product overview

The ECLER PULSO-6 is a 5.5 inch digital control touch panel compatible with several ECLER product families, with an elegant and discreet design that suits any interior.

Its IPS display (720 x 1280 pixels) and capacitive multitouch surface show fully customised user panels for ECLER VIDA and HALO systems, the HUB series (with the ECLER Pilot application) and EclerNet Manager (hosting UCP panels), and it is ready for the ECLER EclerPLEX ecosystem. The PULSO-6 fits standard European flush-mounted electrical boxes and takes its power over the network cable (PoE), so one Cat-5e cable is all it needs; a web interface handles configuration and maintenance.

Key features

• 5.5 inch IPS screen, 720 x 1280 pixels, LED backlight
• Capacitive multitouch panel with 5 touch points
• Web interface for device configuration and management
• Fully customised user panels
• Compatible with ECLER VIDA, HALO, HUB and EclerNet Manager; ready for EclerPLEX
• PoE powered (802.3af), or from an external 12 V DC 2 A supply
• Standard EU round electrical box compatible, horizontal or vertical mounting

One panel, several ECLER systems

The installer chooses the application the PULSO-6 starts with: EclerPLEX user panels, UCP panels of EclerNet Manager (v6.07r1 onwards, where the panel acts as a WPNETTOUCH), VIDA user panels, PILOT for HUB series zoners, or a web browser mode for web-based graphic user interfaces. After each restart the chosen application opens automatically after a 10 second countdown.

Installed in minutes

The mounting bracket fixes with two screws to a standard European round electrical box (screws 60 mm apart), horizontally or vertically. Connect the network cable, then secure the panel with the security screw. With a PoE switch one cable carries data and power; otherwise any standard 12 V DC 2 A supply connects to the Euroblock plug-in connector.

Easy to manage

Configure the panel on its own Admin page or from a browser on the same network: device name, start-up application, time and NTP synchronisation, DHCP or static addressing, backlight (on, dimmed or off after 15 seconds), brightness and rotation (an accelerometer detects the mounting position), manual or scheduled firmware updates and an event log. The status page even shows a live preview of the panel screen.

In the box

• 1 x PULSO-6 control touch panel
• Security screws
• 1 x First Steps Guide
• 1 x warranty card

Available versions

• PULSO-6: reference CPULSO6

ECLER PULSO-6: frequently asked questions

How is the PULSO-6 powered?

By PoE (802.3af, Class 0) through its RJ45 network connector, or from any standard 12 V DC 2 A supply connected to the DC 12V Euroblock connector. The external supply is not part of the package.

Which ECLER systems can the PULSO-6 control?

The ECLER VIDA and HALO series, the HUB series with the ECLER Pilot application and EclerNet Manager (hosting UCP panels); it is also ready for the ECLER EclerPLEX ecosystem.

What kind of wall box does it need?

A standard European round flush-mounted electrical box (fixing screws 60 mm apart), deep enough for the Ethernet cable and its RJ45 connector.

How do I reset it to factory settings?

Remove the frame, press the Factory Reset micro button on the rear with a pin and confirm on the pop-up that appears. All settings, including the administrator password, return to their defaults.

Where can I buy the ECLER PULSO-6 in India?

The ECLER PULSO-6 is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Meeting room control with VIDA

A wall panel for room presets and volume in a corporate meeting room.

Connections

Setup

1. Fix the bracket to the EU round box and connect the network cable.
2. Open the Admin page and select the VIDA application.
3. Log in with the VIDA user that owns the panel.
4. Let the panel restart into the VIDA panel.

Tip: Where several VIDA units share a network, replicate the user panels and users in all of them.

Workflow 2: Restaurant zones with a HUB zoner

Staff control of music source and volume in several zones.

Connections

Setup

1. Install the panel next to the bar or reception.
2. Select PILOT as the start-up application.
3. Link it to the HUB unit on the network.
4. Test source and volume changes in each zone.

Tip: With Pilot one panel can control more than one zone of the HUB installation.

Workflow 3: EclerNet Manager UCP panel

A touch panel for a large EclerNet installation in a hotel or venue.

Connections

Setup

1. Select the UCP application on the panel.
2. Turn on the UCP server switch if required.
3. Add the panel to the project; it acts as a WPNETTOUCH.
4. Load the user control panel and test it.

Tip: Use EclerNet Manager v6.07r1 or later so the project recognises the panel.

Workflow 4: HALO loudspeaker management

Wall control for a HALO based sound system in a gym or shop.

Connections

Setup

1. Mount the panel where staff need it.
2. Power it from the PoE switch.
3. Choose the application for the HALO system.
4. Check the controls the installer prepared.

Tip: Set the backlight to dimmed or off after 15 seconds for energy saving.

Workflow 5: EclerPLEX user panels

Custom control surfaces in the ECLER EclerPLEX ecosystem.

Connections

Setup

1. Create the graphic panels in EclerPLEX.
2. Assign a user to them.
3. Select EclerPLEX on the panel.
4. Enter the user credentials once (Keep me logged in).

Tip: EclerPLEX panels need a user: assign one before testing.

Workflow 6: Panel powered by a 12 V supply

Installations where the network switch has no PoE.

Connections

Setup

1. Wire the supply to the Euroblock plug, respecting polarity.
2. Connect the network cable.
3. Secure the panel to the bracket.
4. Power up: the panel starts automatically.

Tip: Check polarity before applying power to the DC input.