TASCAM DR-10X
MRP - Rs. 19,550
TASCAM DR-10X plug-on recorder for XLR mics: 48 kHz / 24-bit BWF, dual recording and 10 hours on one AAA battery. Available in India from Shivansh Electronics, Kolkata, West Bengal, India.
VISUAL GUIDE — See Every Photo, Spec & Setup Step (PDF)
The price shown is the MAXIMUM RETAIL PRICE (MRP), inclusive of all taxes. For the best price, exclusive offers and discounted rates, delivery timelines, or any other information, please DM us or call +91 89818 07755 / +91 91477 00677. We will gladly share an exclusive coupon code that you can apply at checkout. All payments are processed securely through Razorpay, our trusted payment gateway partner.
General
| Type | Compact plug‑on linear PCM recorder with XLR microphone adapter |
| Display | 96 x 16 OLED |
| Firmware | V2.01 (MP3 and −12 dB dual recording from V2.00) |
Recorder
| Media | microSD (64 MB‑2 GB), microSDHC (4‑32 GB) |
| WAV (BWF) | 44.1 / 48 kHz, 16 / 24‑bit, mono / poly |
| MP3 | 44.1 / 48 kHz; recording 128 / 192 kbps, playback 32‑320 kbps |
| Dual recording | Off, −6 dB, −12 dB |
| Low‑cut filter | 120 Hz (on / off) |
Mic input
| Connector | XLR jack, female (1: GND, 2: HOT, 3: COLD) |
| Input impedance | 10 kΩ or more |
| Mic gain | LO +29 dB, MID +35 dB, HI +45 dB |
| Mic input level (LO / MID / HI, balanced) | Maximum −31 dBu, minimum −63 dBu |
| External input (EXT, unbalanced on hot pin) | Maximum −8 dBu, nominal −24 dBu |
Outputs and USB
| Headphones | 3.5 mm (1/8‑inch) stereo mini jack, dual mono |
| USB | Micro‑B, USB 2.0 High Speed mass storage class |
Audio performance (input to PHONES, 10 kΩ load)
| Frequency response | 20 Hz‑22 kHz, +1 / −2 dB |
| Distortion | 0.05% (1 kHz sine wave, maximum input level) |
| S/N ratio | 92 dB or higher (EXT) 80 dB or higher (mic, LO) |
Battery life (48 kHz / 24-bit WAV, continuous recording)
| Operation time | |
|---|---|
| Alkaline | About 10 hours |
| NiMH | About 8 hours |
| Lithium | About 15.5 hours |
Power and physical
| Power | 1 AAA battery (alkaline, NiMH or lithium) USB bus power from a computer |
| Power consumption | 0.65 W maximum 0.25 A maximum on USB bus power |
| Dimensions (W x H x D, excluding protrusions) | 52 x 94.4 x 28 mm |
| Weight | 68.3 g including battery 56.3 g without battery |
| Operating temperature | 0 to 40 °C |
Product overview
The TASCAM DR-10X is a compact plug-on recorder that attaches directly to the XLR connector of a handheld microphone: the ultimate compact news-gathering system.
A captive XLR connector with a locking clamp holds the DR-10X firmly on the mic, and it records interviews at 48 kHz / 24-bit Broadcast WAV resolution. It works with dynamic mics and with battery-powered condenser mics, so for small-scale reporting all you need is a microphone and the DR-10X: no bulky field recorder, just a compact rig you hold in one hand. Dual recording makes a safety file at a lower level, and the slide record switch, hold function and automatic file closing protect every take. One AAA battery records for at least 10 hours.
| Attaches straight to the mic | XLR plug‑on |
| Broadcast WAV recording | 48 kHz / 24‑bit |
| Safety file at −6 or −12 dB | Dual rec |
| On one AAA alkaline battery | 10 hours |
Key features
- XLR plug-on connection with a clamp nut that locks to the microphone body
- Works with dynamic mics and battery-powered condenser mics; the XLR also accepts an external line signal
- WAV (BWF) at 44.1 / 48 kHz, 16 or 24-bit, mono or poly; MP3 at 128 or 192 kbps (firmware 2.00)
- Dual recording: a second file at −6 or −12 dB as a safety track
- LOW / MID / HIGH mic gain, limiter, auto level and a 120 Hz low-cut filter
- Sliding record switch with one-touch recording and hold function
- Automatic file closing before the battery runs out
- Built-in clock for BWF time information; optional new file about every 15 minutes
- Easy-to-read OLED display, headphone output and playback
- Unit settings can be prepared on a computer as a text file on the microSD card
Record without a cable
Designed for plug-on connection, the DR-10X connects directly to XLR handheld mics for interviews, to mics on stands at press conferences, and to handheld mics in seminars and meetings. Weighing just 56.3 g without its battery, it fits in the palm of the hand, and the locking mechanism gives the whole mic and recorder assembly a solid feel.
Safety first: dual recording, limiter and auto level
Often there is only one chance to get the audio. Dual recording lets you set the main level as high as possible while a backup file is recorded at a lower level at the same time. An automatic gain control adjusts the input level to the input volume, and a limiter guards against sudden loud sounds.
Designed against misoperation
The record switch slides rather than presses, and the hold function stops recording from being interrupted by accidental contact. The OLED display shows the battery level, and if the battery runs out the file is closed automatically so recorded data is kept.
Monitor and check on the spot
Connect headphones to monitor the input while recording and to play back files immediately. On a computer, the DR-10X appears as a USB drive for quick transfer of recordings.
In the box
- TASCAM DR-10X
- USB cable
- Owner's Manual (including warranty)
A microSD or microSDHC card (up to 32 GB), one AAA battery and an XLR microphone are sold separately.
TASCAM DR-10X: frequently asked questions
Which microphones can I use with the DR-10X?
Microphones with an XLR output: dynamic mics and battery-powered condenser mics. The XLR input can also be set to EXT for an unbalanced external line signal.
What is dual recording?
The DR-10X records a second file at a lower level (−6 dB or −12 dB with firmware 2.00) at the same time as the main file, so you have a backup if the main recording overloads.
How long does it record on one battery?
About 10 hours with an alkaline AAA battery, about 8 hours with NiMH and about 15.5 hours with lithium (48 kHz / 24-bit WAV, headphones not connected). USB bus power is also supported.
Can I set up several units the same way?
Yes. Place a settings text file on each microSD card: the DR-10X reads it at start-up and applies the settings, including the clock and a file name word for each unit.
Where can I buy the TASCAM DR-10X in India?
The TASCAM DR-10X is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.
Workflow 1: Street interviews and news gathering
A complete, cable-free recording rig in one hand for reporters.
Connections
| Connect | To |
|---|---|
| Handheld dynamic mic | XLR connector (clamp nut tightened) |
| Headphones | Headphones jack |
Setup
- Insert a AAA battery and a microSD card, then attach the DR-10X to the mic and tighten the clamp nut.
- Set MIC GAIN so the level meter reaches the −12 dB mark.
- Turn on DUAL REC at −6 or −12 dB for a safety file.
- Slide and hold the switch towards REC to record; repeat to stop.
Tip: Hold the microphone, not the recorder, once they are connected.
Workflow 2: Press conferences
Record the speaker's mic on a stand without running cables to a recorder.
Connections
| Connect | To |
|---|---|
| Mic on a stand | XLR connector |
Setup
- Attach the DR-10X to the microphone on the stand.
- Set LIMITER to ON to guard against sudden loud passages.
- Use one-touch recording: from power off, slide and hold towards REC.
- Turn on the hold function to prevent accidental key presses.
Workflow 3: Seminars and meetings
Capture a presenter's handheld mic for long sessions.
Connections
| Connect | To |
|---|---|
| Presenter's handheld mic | XLR connector |
| Computer | Micro‑B USB port (included cable) |
Setup
- Set TIME TRK INC to ON so a new file starts about every 15 minutes.
- Use AUTO LEVEL for speakers with changing voice levels.
- Record; the built-in clock adds time information to the BWF files.
- Copy the files to a computer: choose STORAGE when connected by USB.
Tip: Choose MP3 recording for very long sessions (firmware 2.00 or later).
Workflow 4: Several reporters, one setup
Prepare a team of DR-10X recorders identically from a computer.
Connections
| Connect | To |
|---|---|
| Settings file DR‑10_SysPara.txt | Root of each microSD card |
Setup
- Write the settings you want between <dr10_syspara> tags in a text file.
- Give each unit its own file name word, for example DR0001 and DR0002.
- Copy the file to the root of each card and turn the units on.
- Each unit applies the settings and deletes the file.
Tip: The <date> and <time> tags set the clock of every unit at once.
Workflow 5: Recording a line signal
Record an external audio signal through the XLR connector.
Connections
| Connect | To |
|---|---|
| Line‑level source (XLR cable) | XLR connector |
Setup
- Set MIC GAIN to EXT (unbalanced input on the hot pin).
- Keep the source level within the −8 dBu maximum input level.
- Monitor on headphones to check the level.
- Record in WAV 48 kHz / 24-bit.
Workflow 6: Checking and delivering recordings
Review takes on the spot and send them on quickly.
Connections
| Connect | To |
|---|---|
| Headphones | Headphones jack |
| Computer | Micro‑B USB port |
Setup
- Press ENTER to play the latest file; hold MENU to see its remaining time.
- Search backward or forward by holding the skip buttons.
- Connect to a computer and choose STORAGE; the unit appears as a drive named DR-10.
- Copy the WAV or MP3 files for editing or delivery.
Tip: Choose POWER instead to run the recorder on USB bus power.
