XVIVE A58 Guitar Wireless System

Product overview

The XVIVE A58 Guitar Wireless System is a 5.8 GHz True Diversity wireless system for guitar, bass and any instrument with a 1/4 inch output jack, with 24-bit / 48 kHz audio, 5 ms latency and automatic scanning for the best wireless channel.

The transmitter plugs into the instrument and the receiver into the amplifier, amp modeler, effect pedal or audio interface: any connection normally made with a 1/4 inch cable can go wireless. The 5.8 GHz band is less crowded than 2.4 GHz, so interference from other wireless devices is less likely, and the range reaches up to 30.48 m / 100 ft. The A58 comes in four finishes: Mahogany, Rosewood, Sunburst and Grey.

Key features

• 5.8 GHz True Diversity wireless system
• High-resolution 24-bit / 48 kHz audio, 110 dB signal-to-noise ratio
• 5 ms latency
• Up to 5 hours of battery life, USB-C charging
• 6 wireless channels; up to six A58 sets in one area
• Range up to 30.48 m / 100 ft (line of sight)
• Passive and Active modes for any pickup
• Automatically selects the best channel
• Open-battery-compartment design

Sound great with 5.8

Rock-solid wireless connections with high-resolution 24-bit / 48 kHz audio, imperceptibly low latency (5 ms) and super-clean sound (signal-to-noise ratio 110 dB), with a frequency response of 20 Hz - 20 kHz (-3 dB).

Smart channel scanner

The system offers six wireless channels and can scan them to choose the one with the strongest, clearest signal. In a new venue, hold the receiver's channel button for 3 seconds to find and set the best channel, then set the transmitter to the same one. When both units are switched off and on again, the last channel is recalled.

Active or passive

Passive and Active modes let you use instruments with any kind of pickup, from vintage passive to high-gain active. Hold the transmitter's channel button for 3 seconds for Active mode; the Active LED lights.

Charge it

Charge the transmitter and receiver at the same time using the dual USB-C cable and any 5 V / 2 A USB power supply. Two and a half hours of charging give 5 hours of play, 1.25 hours give 2 hours, and 30 minutes give 1 hour. A rugged, compact carry case protects the transmitter, receiver and cable.

Available versions

• Mahogany (A58System-Mahogany)
• Rosewood (A58System-Rosewood)
• Sunburst (A58System-Sunburst)
• Grey (A58System-Grey)

In the box

• Transmitter
• Receiver
• USB-C charging cable
• Case
• Manual

FAQs

Can the XVIVE A58 be used with a bass or an acoustic guitar?

Yes. It is for guitar, bass and any instrument with a 1/4 inch output jack, including piezo-electric acoustic guitars, with Passive and Active modes for any pickup.

How many A58 systems can be used together?

Up to six A58 sets can be used simultaneously in one area, each on its own channel.

Can I play while the A58 is charging?

The units can be used while charging, but XVIVE advises not to leave the batteries plugged in and fully charged for extended periods.

Where can I buy the XVIVE A58 Guitar Wireless System in India?

The XVIVE A58 Guitar Wireless System is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Wireless guitar to the amplifier

Guitarists on stage, at rehearsal or at home.

Connections

Setup

1. Plug the transmitter into the guitar and the receiver into the amplifier.
2. Switch both on and set the same channel.
3. Check that the green RF LED on the receiver is on.
4. Play.

Tip: The last channel is recalled at the next switch-on.

Workflow 2: Bass with active pickups

Bassists with active or high-output instruments.

Connections

Setup

1. Plug in transmitter and receiver.
2. Hold the transmitter's channel button for 3 seconds: the Active LED lights.
3. Match the channels and play.

Tip: If the sound distorts, switch to Active mode.

Workflow 3: Into a pedalboard or amp modeler

Players with effects and modelers.

Connections

Setup

1. Plug the receiver into the pedalboard or modeler input.
2. Set both units to the same channel.
3. Play through the effects as usual.

Tip: Two sets can cover instrument to effects and effects to amplifier.

Workflow 4: Acoustic guitar to a PA mixer

Acoustic performers with piezo-electric pickups.

Connections

Setup

1. Plug the transmitter into the guitar's output jack.
2. Plug the receiver into the PA mixer.
3. Match the channels and set the level at the mixer.

Tip: The A58 also feeds a digital recorder.

Workflow 5: New venue, best channel

Gigging players moving between venues.

Connections

Setup

1. Hold the receiver's channel button for 3 seconds.
2. Wait for the channel LED to stay on the best channel.
3. Set the transmitter to the same channel.

Tip: Keep the receiver more than 3 m from Wi-Fi routers.

Workflow 6: Charging between sets

Players on long gigs.

Connections

Setup

1. Connect both units to the dual USB-C cable.
2. Plug it into a 5 V / 2 A USB supply.
3. 30 minutes of charging give about 1 hour of play.

Tip: A full charge (2.5 hours) gives up to 5 hours.