ECLER WPaVOLUS

Product overview

The ECLER WPaVOLUS is a remote wall panel control for one volume management, made in the standard format of the WPa series for US electrical boxes. It works with every ECLER device that has a 0-10 V DC REMOTE control port, such as the NXA series, GPA series, MIMO88, MPA-R, ALMA and CA series, and connects over one RJ45 cable. The WPa series has a modern, elegant and discreet design, and a surface-mount installation box is included.

WPa is ECLER's series of remote control wall panels for systems and for interconnecting audio signals, with a modern, elegant and discreet design in white (RAL 9016). Every panel of the series comes with a surface-mount installation box, and a magnetic frame holds the front plate in place.

Key features

• LEVEL knob for remote volume control (0-10 V DC)
• RJ45 connection for control voltage and power
• US format, compatible with US electrical boxes
• Surface-mount installation box included

Works with ECLER REMOTE ports

The WPaVOLUS sends a 0-10 V DC control voltage over a standard RJ45 cable: pin 2 carries the remote volume (10 V = minimum, 0 V = maximum) and pin 6 the +10 V / +12 V supply from the controlled device. It is compatible with ECLER devices that have a 0-10 V DC REMOTE port, such as the NXA series, GPA series, MIMO88, MPA-R, ALMA and CA series.

Made for US electrical boxes

The WPaVOLUS keeps the standard WPa look in the US format (116.5 x 114.8 x 30.8 mm) and fits US electrical boxes.

In the box

• 1 x WPaVOLUS wall panel
• 1 x surface-mount installation box

ECLER WPaVOLUS: frequently asked questions

Which ECLER devices work with the WPaVOLUS?

Any ECLER device with a 0-10 V DC REMOTE port, such as the NXA series, GPA series, MIMO88, MPA-R, ALMA and CA series.

What cable does it use?

A standard RJ45 network cable, wired as in the connection diagram (pins 2, 6 and a GND pin).

What size is it?

116.5 x 114.8 x 30.8 mm, 0.13 kg.

Where can I buy the ECLER WPaVOLUS in India?

The ECLER WPaVOLUS is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Zone volume in a shop

Retail spaces that want staff to set the music level at the wall.

Connections

Setup

1. Run a network cable from the panel to the REMOTE port.
2. Wire pin 2 (remote volume), pin 6 (VCC) and a GND pin as in the connection diagram.
3. Turn LEVEL and check the zone volume follows.

Tip: Turning LEVEL fully clockwise gives maximum volume (0 V on pin 2).

Workflow 2: Meeting room level control

Corporate rooms with their own speaker zone.

Connections

Setup

1. Mount the panel by the door.
2. Connect it to the REMOTE port of the zone.
3. Set the maximum level on the amplifier, then hand control to the panel.

Tip: One panel controls one volume.

Workflow 3: Restaurant and bar music

Leisure venues where the level changes through the day.

Connections

Setup

1. Install the panel where staff can reach it.
2. Connect the RJ45 cable.
3. Adjust LEVEL during service.

Tip: The discreet white panel suits most interiors.

Workflow 4: US electrical boxes

Projects that use US format back boxes.

Connections

Setup

1. Fit the panel to a US electrical box.
2. Connect the RJ45 cable to the REMOTE port.
3. Test the LEVEL control.

Tip: The WPaVOLUS keeps the WPa look in the US format.

Workflow 5: Several zones, several panels

Venues with more than one area.

Connections

Setup

1. Install one panel in each zone.
2. Wire each one to the REMOTE port of its zone.
3. Label the cables during installation.

Tip: Multi-channel devices have one REMOTE port per channel (CH 1 to CH 4 in the diagram).

Workflow 6: Mounting the panel

Installers fitting the panel to a wall.

Connections

Setup

1. Fix the surface-mount box (or an in-wall box) where the panel is needed.
2. Wire the cable to the screw terminals of module B; no soldering is needed.
3. Screw module B into the box, then fit the magnetic frame C.
4. Press the front plate A into place with care: the frame magnets exert considerable force.

Tip: The surface-mount box is included.