ELECTRO-VOICE ELX200 10

Product overview

The ELECTRO-VOICE ELX200 10 is a passive 10-inch two-way loudspeaker from the ELX200 series: a high-output EVS-10M woofer and DH-1L 1.4-inch titanium compression driver on EV's patented SST waveguide, 127 dB maximum SPL, 300 W continuous / 1200 W peak, in black or white.

Every aspect of the ELX200 is designed for ideal results as part of the whole: the acoustical, electrical and mechanical components work together seamlessly. The low-profile full-range form factor uses a high-spec composite enclosure to balance weight, manageability and structural integrity, and EV's quality and testing procedures yield accurate, linear response at the system's highest output levels: loud and clear all the way up to the limit.

Key features

• 1200 W peak, 127 dB peak SPL system, reliability verified with over 500 hours of abuse testing and endurance testing to 4x typical industry practices
• 1.4-inch DH-1L (1-inch exit) titanium compression driver for extended, transparent high-frequency response
• High-output EVS-10M woofer for durability and low-frequency reproduction
• EV-patented Signal Synchronized Transducers (SST) waveguide: precise, consistent coverage, minimal distortion, maximised acoustical loading
• Three M10 threaded points for forged eyebolts, integrated pole mount and the proven two-handle design
• Two parallel locking 4-pole speaker connectors

Set up anywhere

The ELX200 10 mounts on a tripod stand or on a pole above a subwoofer. It can also work as a stage monitor, or be flown from its three M10 suspension points with certified rigging hardware (never in a vertical column array).

Connecting the amplifier

Pins 1+ and 1- carry the signal; pins 2+ and 2- are not used. The two connectors are wired in parallel, so further cabinets can be linked: one cabinet is an 8 Ω load (minimum 7.2 Ω), two 4 Ω, three 2.7 Ω and four 2 Ω per amplifier channel. Do not exceed the amplifier's maximum load rating, and apply the recommended 55 Hz high-pass filter.

Optional accessories

• EBK1-M10-3PACK forged M10 short shank eyebolt kit
• ELX200-10-CVR padded cover
• ELX200-BRKT / ELX200-BRKT-W wall mount bracket, black / white
• BRKT-POLE-S pole mount bracket (8-, 10- and some 12-inch)

Available versions

• ELX200-10: black
• ELX200-10-W: white

In the box

• ELX200-10 loudspeaker

ELECTRO-VOICE ELX200 10: frequently asked questions

Is it powered?

No. The ELX200 10 is passive: drive it from an amplifier that can handle an 8 Ω load (300 W continuous, 1200 W peak).

Can it be used as a stage monitor?

Yes. EV shows the full-range ELX200 models in the monitor position as one of the recommended configurations.

Can it be flown?

Yes, from the three M10 suspension points with forged eyebolts and certified rigging hardware, installed by an authorised rigging professional. Never suspend ELX200 loudspeakers in a vertical column array.

Which colours are available?

Black (ELX200-10) and white (ELX200-10-W).

Where can I buy the ELECTRO-VOICE ELX200 10 in India?

The ELECTRO-VOICE ELX200 10 is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.

Workflow 1: Basic stereo system

Bands, DJs and events.

Connections

Setup

1. Mount the cabinets on tripods.
2. Set a 55 Hz high-pass filter.
3. Connect pins 1+ / 1-.
4. Set levels.

Tip: One cabinet per channel is an 8 Ω load.

Workflow 2: Stage monitors

Performers on stage.

Connections

Setup

1. Lay the cabinets in monitor position.
2. Feed a monitor mix per channel.
3. Link up to four per channel.
4. Check the amplifier load.

Tip: Four cabinets on one channel present 2 Ω nominal.

Workflow 3: Tops on subwoofers

Bigger events needing more low end.

Connections

Setup

1. Fit an M20 pole into the subwoofer's pole cup.
2. Set the full-range cabinet's pole cup on the pole.
3. Secure it.
4. Check the combined load.

Tip: Stacking adds low end without extra amplifier channels.

Workflow 4: House of worship

Churches and halls.

Connections

Setup

1. Fit the optional ELX200-BRKT wall bracket.
2. Aim the 90° x 60° pattern at the seating.
3. Set the high-pass filter.
4. Equalise for speech.

Tip: White versions blend into light interiors.

Workflow 5: Flown installation

Clubs and venues.

Connections

Setup

1. Fit forged M10 eyebolts.
2. Use certified rigging hardware.
3. Never form a vertical column array.
4. Add a safety.

Tip: Rigging must be done by an authorised rigging professional.

Workflow 6: Mobile gig

Working musicians.

Connections

Setup

1. Carry by the handles.
2. Set up on tripods with fully extended legs.
3. Connect and set levels.
4. Use the padded cover in transit.

Tip: Two people should lift heavier loudspeakers.