






FYNE AUDIO F500SP
PRICE ON ENQUIRY
Fyne Audio F500SP: UK-built 2-way stand-mount with 6-inch SP IsoFlare point source driver, BassTrax diffuser and bi-wire terminals. Available in India from Shivansh Electronics, Kolkata, West Bengal, India.
VISUAL GUIDE — See Every Photo, Spec & Setup Step (PDF)
PRICE ON ENQUIRY. For the price, exclusive offers, delivery timelines, or any other information, please Contact / WhatsApp +91 89818 07755 / +91 91477 00677. We will gladly share a personalised quotation for Shivansh Electronics, Kolkata, West Bengal, India. All payments are processed securely through Razorpay, our secure payment gateway.
General
| System type | 2-way, downward-firing port with BassTrax Tractrix diffuser |
| Nominal impedance | 8 Ω |
| Frequency response (-6 dB, typical in room) | 42 Hz - 34 kHz |
| Sensitivity (2.83 V/1 m) | 90 dB |
Power
| Recommended amplifier power | 30 - 120 W RMS |
| Continuous power handling | 60 W RMS |
| Peak power handling | 240 W |
Drivers
| IsoFlare point source driver | 1 × 150 mm (6-inch) SP IsoFlare point source driver: multi-fibre bass / midrange cone, FyneFlute surround, 25 mm magnesium dome compression tweeter, neodymium magnet system |
Crossover
| Crossover frequency | 1.7 kHz |
| Crossover type | Bi-wired passive low loss, 2nd order low pass, 1st order high pass, Cryo-Lite treated |
Physical
| Cabinet construction | High-density fibreboard with extensive internal bracing |
| Dimensions (H × W × D) | 323 × 200 × 320 mm (12.7 × 7.9 × 12.6 in) |
| Dimensions include | Grille, terminals and plinth; feet excluded |
| Net weight, each | 8.1 kg (17.6 lb) |
| S-Trax position (from cabinet front edge) | 44 mm (1.7 in) |
| SuperTrax position (from cabinet front edge) | 20 mm (0.8 in) |
Finishes
| Finish options | Piano Gloss Black, Piano Gloss White, Piano Gloss Walnut, Natural Walnut |
Versions
| F80000381 | Piano Gloss Black |
| F80000382 | Piano Gloss White |
| F80000380 | Piano Gloss Walnut |
| F80000383 | Natural Walnut |
Product overview
The Fyne Audio F500SP is the smallest loudspeaker in the UK-built F500 SP Special Production Series: a 2-way stand-mount with a 6-inch (150 mm) SP IsoFlare point source driver, a tuned crossover and the premium BassTrax port system derived from the F700 Series.
The F500SP takes the F500 stand-mount cabinet and adds a unique Special Production IsoFlare driver, a tuned crossover and the premium BassTrax port system, all derived from the F700 Series. Its 150 mm SP IsoFlare driver delivers full-range, point source reproduction across the entire audio spectrum for outstanding detail and imaging, and its multi-fibre cone gets its bass from a twin-magnet motor system and a FyneFlute roll surround that reduces cone resonances at the driver termination.
The F500 SP Series blends the refinements of F700 Series technology with the classic F500 cabinet design. The SP IsoFlare driver is a direct derivative of the F700 point source units: a powerful neodymium motor with a vented rear chamber moves the tweeter's fundamental resonance well below the crossover point, a computer-modelled HF waveguide gives a flat response out to its 30 kHz design parameters, and heatsinking through a metal pole piece keeps the treble smooth even after long, loud listening. The bespoke multi-fibre cone sits in a rigid cast aluminium chassis with a separate flux focusing magnet for low-frequency efficiency.
The low-frequency output is channelled through a downward-firing port onto the BassTrax Tractrix diffuser, which converts plane-wave port energy into a spherical 360-degree wavefront that exits evenly through the plinth. Bass is smooth and the speaker is much less critical of room position. On the F500SP the system is built into an anodised aluminium plinth beneath the cabinet.
The crossover uses low-loss laminated core inductors, high-grade polypropylene capacitors and silver-plated OFC internal wiring treated by Fyne Audio's Cryo-Lite process: the wiring is super-frozen to -170 °C and slowly thawed over several days to relieve micro-stresses, for greater transparency. A bi-wire terminal panel adds a fifth terminal to ground the driver chassis and drain amplifier- or cable-borne RF interference. The higher-density fibreboard cabinet is internally braced and damped with bonded acoustic fibre and polyether foam, and every pair is designed, built, hand finished and pair matched in Fyne Audio's UK factory.
| Frequency response (-6 dB, typical in room) | 42 Hz - 34 kHz |
| Sensitivity (2.83 V/1 m) | 90 dB |
| Recommended amplifier power (RMS) | 30 - 120 W |
| SP IsoFlare point source driver | 6-inch |
Key features
- UK-built Special Production 2-way stand-mount, hand built and finished in Glasgow
- 150 mm SP IsoFlare point source driver with 25 mm magnesium dome compression tweeter at its centre
- Twin-magnet motor system and FyneFlute roll surround for deep, controlled bass
- BassTrax Tractrix diffuser with downward-firing port for a smooth, even 360-degree bass wavefront
- Computer-modelled HF waveguide, vented rear chamber and metal pole piece heatsinking
- Crossover with low-loss laminated core inductors, polypropylene capacitors and Cryo-Lite treated silver-plated OFC wiring
- Bi-wire terminal panel with a fifth terminal for driver chassis grounding
- Anodised aluminium plinth
- Higher-density fibreboard cabinet, internally braced, with driver rears coupled to the bracing by damping mastic
- Diamond machine-cut aluminium driver trim; Piano Gloss Black, Piano Gloss White, Piano Gloss Walnut or Natural Walnut
- Magnetically attached grille
Made for
- Stereo systems in compact living rooms, bedrooms and studies
- Stand mounting on the matching FS6 stand
- Surround or front channels of a home cinema system
- Listeners who want UK-built, hand-finished loudspeakers in a compact size
Placement and set-up
- Stereo: about 1.5 - 4.5 m (5 - 15 ft) apart
- Ideally no closer than 0.5 m (20 in) to the rear wall and 1 m (3 ft) to the side walls
- Experiment with toe-in towards the listener for the best stereo imaging
- On wooden or delicate surfaces use stick-on feet to protect the surface
- Run in for around 40 hours at normal listening levels
In the box
- F500SP loudspeaker with magnetic grille
Connections
- Bi-wire terminal panel: one pair for HF, one pair for LF, with link bars for single wiring
- Fifth terminal: earth / ground connection to the driver chassis (optional use)
- Accepts bare wire or 4 mm plugs
Finishes
- Piano Gloss Black
- Piano Gloss White
- Piano Gloss Walnut (lacquered real wood veneer)
- Natural Walnut veneer
Fyne Audio F500SP: frequently asked questions
What amplifier suits the F500SP?
Fyne Audio recommends 30 - 120 W RMS into the F500SP's 8 Ω nominal impedance. Power handling is 60 W RMS continuous and 240 W peak, and sensitivity is 90 dB (2.83 V/1 m).
Can the F500SP be bi-wired?
Yes. There are two pairs of terminals, one for the HF and one for the LF. Keep the link bars in place for a single cable, or remove them and use two sets of cable or a dedicated bi-wire cable, which Fyne Audio says gives the best possible sound quality.
What is the fifth terminal for?
It connects to the drive unit chassis so that radio frequency interference can be grounded rather than passed back to the amplifier, where it would reduce fine detail. A separate earth wire can be used, but the best results come from a dedicated screened loudspeaker cable.
What does BassTrax do?
The downward-firing port feeds a Tractrix profile cone that turns the port energy into a 360-degree wavefront leaving evenly through the plinth. Bass is smoother and the speaker is much less critical of room position than a conventional ported design.
Should I listen with the grille on or off?
The magnetic grille is designed for maximum transparency, but Fyne Audio recommends removing it for the best sound.
Where can I buy the Fyne Audio F500SP in India?
The Fyne Audio F500SP is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.
Workflow 1: Compact stereo system on stands
Music lovers who want detailed, natural stereo from a UK-built pair in a smaller room.
Connections
| Connect | To |
|---|---|
| Integrated amplifier left speaker output | Left F500SP terminals |
| Integrated amplifier right speaker output | Right F500SP terminals |
Setup
- Place each F500SP on a rigid stand such as the FS6, with the tweeter roughly at ear height when seated.
- Set the speakers about 1.5 - 4.5 m apart, ideally 0.5 m from the rear wall and 1 m from the side walls.
- With the amplifier switched off, connect positive to positive and negative to negative, keeping the link bars in place for single wiring.
- Toe the speakers in towards the listening seat until the stereo image locks in.
- Remove the grilles for the best sound.
Tip: Choose an amplifier in the 30 - 120 W RMS range and allow around 40 hours of normal listening for the speakers to run in.
Workflow 2: Bi-wired system with chassis earth
Listeners who want the last degree of detail from their amplifier and cables.
Connections
| Connect | To |
|---|---|
| Amplifier speaker outputs (via two cable sets or a bi-wire cable) | F500SP HF and LF terminals, link bars removed |
| Screened loudspeaker cable screen or separate earth wire | F500SP earth terminal |
Setup
- Switch the amplifier off.
- Remove the link bars between the HF and LF terminals.
- Run two sets of cable, or a dedicated bi-wire cable, from each amplifier channel to the HF and LF terminals.
- Optionally connect the fifth terminal to ground with a separate earth wire or, better, a dedicated screened loudspeaker cable.
- Check every connection is positive to positive and negative to negative before switching on.
Tip: Grounding the driver chassis drains radio frequency interference that would otherwise reduce fine detail and resolution.
Workflow 3: Home cinema surround or front pair
Families building a living-room cinema around a TV and an AV receiver.
Connections
| Connect | To |
|---|---|
| TV with HDMI eARC | AV receiver HDMI eARC input |
| AV receiver front or surround left / right outputs | F500SP pair |
| AV receiver subwoofer output | Powered subwoofer |
Setup
- Place the F500SP pair either side of the TV or beside and slightly behind the seating for surrounds, toed in towards the main seat.
- Wire each speaker to the receiver with the receiver switched off.
- Add a matching F57SP-6 or F57SP-8 centre speaker, voiced to integrate with the F500SP models, so dialogue matches the front pair.
- Run the receiver's speaker set-up so levels, distances and crossover suit the room.
Tip: The point source IsoFlare driver keeps voices and effects focused as they move across the room.
Workflow 4: Living room close to the wall
Apartments where the speakers cannot stand far out into the room.
Connections
| Connect | To |
|---|---|
| Stereo amplifier speaker outputs | F500SP pair |
Setup
- Place the speakers as far from the walls as the room allows, ideally at least 0.5 m from the rear wall.
- Let the BassTrax diffuser spread the port output in a 360-degree wavefront through the plinth.
- Play familiar bass-rich music and move the speakers a little at a time until the bass sounds even.
- Fine-tune the toe-in for imaging.
Tip: BassTrax makes the speaker much less critical of room positioning than a conventional port.
Workflow 5: Vinyl corner
Record collectors with a turntable and a stereo amplifier with a phono input.
Connections
| Connect | To |
|---|---|
| Turntable | Amplifier phono input |
| Amplifier speaker outputs | F500SP pair |
Setup
- Keep the turntable on a solid surface away from the speakers.
- Connect the turntable to the phono input and the amplifier to the speakers.
- Mount the speakers on rigid stands so the cabinets stay steady.
- Set the toe-in so voices sit in the centre between the speakers.
Tip: Run the speakers in for around 40 hours before judging the sound.
Workflow 6: Streaming and TV in one stereo system
Living rooms where one stereo pair serves music streaming and the TV.
Connections
| Connect | To |
|---|---|
| Network streamer | Integrated amplifier line input |
| TV audio output | Amplifier HDMI ARC or optical input (as the amplifier provides) |
| Amplifier speaker outputs | F500SP pair |
Setup
- Place a speaker either side of the TV, about 1.5 - 4.5 m apart.
- Connect the streamer and the TV to the amplifier.
- Wire the F500SP pair to the amplifier's speaker outputs.
- Set the TV to send its sound to the external audio output.
Tip: Clean the gloss or veneer cabinets only with a microfibre cloth, and keep them out of direct sunlight.








