









FYNE AUDIO FA502iC LCR
PRICE ON ENQUIRY
Fyne Audio FA502iC LCR: 8-inch IsoFlare in-ceiling / in-wall speaker with driver angled 15° for home theatre left, centre and right. Available in India from Shivansh Electronics, Kolkata, West Bengal, India.
VISUAL GUIDE — See Every Photo, Spec & Setup Step (PDF)
PRICE ON ENQUIRY. For the price, exclusive offers, delivery timelines, or any other information, please Contact / WhatsApp +91 89818 07755 / +91 91477 00677. We will gladly share a personalised quotation for Shivansh Electronics, Kolkata, West Bengal, India. All payments are processed securely through Razorpay, our secure payment gateway.
General
| System type | 2 way IsoFlare loudspeaker for in-ceiling or in-wall application, angled dispersion for LCR applications |
| Frequency response (-6 dB, typical in room) | 35 Hz - 34 kHz |
| Sensitivity (2.83 V @ 1 m) | 91 dB |
| Nominal impedance | 8 Ω |
Power
| Recommended amplifier power | 30 - 150 W RMS |
| Power handling, continuous | 75 W RMS |
| Power handling, peak | 300 W |
Drivers and crossover
| Drive unit complement | 1 × 200 mm (8 in) IsoFlare point source driver, multi-fibre bass / midrange cone, FyneFlute surround with 25 mm titanium dome compression tweeter |
| Driver angle | 15 degrees to the mounting surface |
| Crossover frequency | 1.7 kHz |
| Crossover type | Passive 2nd order low pass, 1st order high pass |
Installation
| Dimensions (diameter × depth) | 278 × 157 mm (10.9 × 6.2 in) |
| Cut-out diameter | 255 mm (10.0 in) |
| Depth behind mounting surface | 155 mm (6.1 in) |
| Clamp travel | 0 - 26 mm (0 - 1.0 in) |
| Suggested minimum volume | 18 L |
| Round grille diameter | 288 mm (11.3 in) |
| Square grille | Not available |
| Net weight (each) | 2.4 kg (5.2 lb) |
Product overview
The Fyne Audio FA502iC LCR is the angled-driver version of the FA502iC in-ceiling / in-wall loudspeaker, for installations where the speaker is offset from the listening position: its 200 mm (8-inch) IsoFlare point source driver with 25 mm titanium dome compression tweeter is angled at 15 degrees to the mounting surface and can be turned in the cut-out to aim straight at the main seats.
The FA502iC LCR is part of the FA500iC Series, Fyne Audio's flagship home install range, built around the same IsoFlare drivers as the F500 free-standing loudspeakers. It is ideal for the left, centre and right channels of home theatre systems, where the speakers usually sit in the ceiling or wall at an angle to the seating rather than directly in front of it.
The IsoFlare driver is mounted at an angle in the baffle moulding. Because the speaker is round, the driver can be orientated in the cut-out so the angled output points directly towards the centre of the primary listening area. A highly rigid titanium dome compression tweeter sits at the heart of the multi-fibre bass / midrange cone with FyneFlute roll surround, giving constant directivity and outstanding imaging, with perfect time alignment from a single point.
It shares the easy fitment, power and performance of the standard FA502iC: 91 dB sensitivity (2.83 V @ 1 m), 8 Ω nominal impedance, power handling of 75 W continuous and 300 W peak, and a crossover at 1.7 kHz built with low-loss laminated core inductors and high-grade polyester capacitors, tuned for a flush-fit infinite baffle position.
Installation uses a 255 mm cut-out made with the supplied mounting template, self-aligning clamps for boards up to 26 mm thick and spring clip cable terminals. The FA502iC LCR is supplied with a paintable, low-profile round magnetic grille; a square grille is not available for this model.
| Angled IsoFlare driver | 15° |
| Frequency response (-6 dB, in room) | 35 Hz - 34 kHz |
| Sensitivity (2.83 V @ 1 m) | 91 dB |
| IsoFlare point source driver | 200 mm |
Key features
- 2-way IsoFlare loudspeaker for in-ceiling or in-wall application, angled dispersion for LCR applications
- Driver angled at 15 degrees to the mounting surface, orientable in the round cut-out
- 200 mm (8-inch) IsoFlare point source driver with multi-fibre bass / midrange cone and FyneFlute surround
- 25 mm titanium dome compression tweeter at the heart of the cone
- Crossover based on the F500 Series, low-loss laminated core inductors and polyester capacitors
- Sensitivity: 91 dB (2.83 V @ 1 m), nominal impedance 8 Ω
- Power handling: 75 W continuous, 300 W peak
- Self-aligning clamps, 0 - 26 mm clamp travel
- Spring clip cable terminals
- Paintable low-profile round magnetic grille
Made for
- Left, centre and right channels of home theatre systems
- Installations where the speaker position is offset from the listening position
- In-ceiling front channels above a TV or projection screen
- In-wall channels where the speaker cannot face the seats directly
In the box
- 1 × 8-inch IsoFlare loudspeaker
- 1 × round grille
- 1 × mounting template
Connections
- Two spring clip speaker terminals (positive and negative)
Fyne Audio FA502iC LCR: frequently asked questions
How is the FA502iC LCR different from the FA502iC?
Its 200 mm IsoFlare driver is angled at 15 degrees to the mounting surface, so the sound can be aimed at the seats when the speaker is offset from the listening position. It has the same power and performance as the standard FA502iC, a deeper 155 mm build, a 255 mm cut-out and a round grille only.
How do I aim it at the listening position?
Before tightening the clamps, rotate the speaker in the round cut-out so the angled IsoFlare driver points towards the centre of the primary listening area.
What size hole and depth does it need?
The cut-out diameter is 255 mm and the depth behind the mounting surface is 155 mm. Clamp travel is 0 - 26 mm and the suggested minimum enclosure volume is 18 L.
Is a square grille available?
No. The FA502iC LCR is supplied with a paintable low-profile round grille, and a square grille is not available for this model.
What amplifier power does it need?
Recommended amplifier power is 30 - 150 W RMS. Power handling is 75 W continuous and 300 W peak.
Where can I buy the Fyne Audio FA502iC LCR in India?
The Fyne Audio FA502iC LCR is available from Shivansh Electronics, Kolkata, West Bengal, India, with delivery across India.
Workflow 1: In-ceiling LCR above a projection screen
Home cinemas where the front speakers must go in the ceiling ahead of the seats.
Connections
| Connect | To |
|---|---|
| AV receiver front left, centre and right outputs | Three FA502iC LCR spring terminals |
Setup
- Mark three positions in the ceiling across the width of the screen.
- Check for joists, pipes and cables, fix the template and cut the 255 mm openings with a keyhole saw.
- Connect good quality speaker cable to the spring terminals, positive to positive and negative to negative.
- Fit each speaker and rotate it so the angled driver points towards the centre of the seating, then tighten the clamps gently.
- Snap on the round grilles and run the receiver's speaker calibration.
Tip: The 15-degree driver angle directs dialogue and effects towards the listeners instead of straight down to the floor.
Workflow 2: Living-room TV with in-ceiling front channels
Living rooms where the TV sits on the wall and floor speakers are not wanted.
Connections
| Connect | To |
|---|---|
| AV receiver front left / centre / right outputs (30 - 150 W RMS) | FA502iC LCR above and either side of the TV |
Setup
- Place the centre speaker in the ceiling above the TV and the left and right speakers either side.
- Install them with the cut-out template and self-aligning clamps.
- Aim each angled driver at the sofa.
- Set the speaker distances and levels in the AV receiver.
Tip: Paint the grilles to match the ceiling so the speakers disappear.
Workflow 3: In-wall LCR beside a screen
Media rooms where the wall speakers sit wide of the seating.
Connections
| Connect | To |
|---|---|
| AV receiver front outputs | FA502iC LCR in the wall |
Setup
- Check the wall cavity gives at least 155 mm depth and about 18 L of volume.
- Cut the 255 mm openings and fit the speakers; the clamps grip boards up to 26 mm thick.
- Turn each speaker so the driver angles in towards the main seat.
- Fit the grilles and calibrate the system.
Tip: Orienting the driver towards the listener keeps the front image focused even with wide speaker spacing.
Workflow 4: Complete in-ceiling 5.1 system
Homes that want an all-ceiling home theatre in the FA500iC Series.
Connections
| Connect | To |
|---|---|
| AV receiver front channels | Three FA502iC LCR |
| AV receiver surround channels | FA500iC Series speakers in the ceiling |
Setup
- Use FA502iC LCR for the front left, centre and right, where the speakers are offset from the seats.
- Use standard FA500iC Series models for the surround positions.
- Install all speakers with their templates and clamps.
- Run the receiver's set-up and match the levels.
Tip: The LCR uses the same IsoFlare driver as the FA502iC, so the front and surround channels match tonally.
Workflow 5: Careful installation and safety
Installers fitting the speakers in ceilings with lights, ducts or services.
Connections
| Connect | To |
|---|---|
| Speaker cable (low smoke / halogen-free where required) | FA502iC LCR spring terminals |
Setup
- Use a stud locator to avoid joists, and check for water or gas pipes and cables.
- Fit a suitably approved fire hood where building regulations require one.
- Leave enough cable length to fit or remove the speaker easily.
- Tighten the clamp screws carefully; set a cordless screwdriver to its lowest clutch setting.
Tip: Always connect the speaker to a suitable amplifier, never to a mains supply.
Workflow 6: Painting the round grille
Interiors with coloured ceilings or walls.
Connections
| Connect | To |
|---|---|
| Magnetic round grille | FA502iC LCR baffle |
Setup
- Carefully remove the scrim material from the rear of the grille.
- Paint by brush or aerosol in several thin coats so the perforations are not blocked.
- Re-apply the scrim with a light coating of aerosol fabric adhesive.
- Offer the grille up and let the magnets snap it into position.
Tip: Thin coats keep the grille acoustically transparent.








